D-Link Australia & New Zealand Support Resources
Home
Technical Support
Check Warranty Status
Warranty/RMA procedure
Check RMA Status
Contact Us
Download
DSL-G604T_NZ
REV A
Download direct:
http://files.dlink.com.au/products/DSL-G604T_NZ/REV_A/Firmware
Firmware
V3.00B02.NZ_20060711* Fixed P2P lockups. * Increased DSLAM support. * Changed default Wizard time zone to �(GMT+12:00) Wellington, Auckland�v2.00B01T01.NZ_20051123* ADSL2/2+ Support===================================================================v1.00B07.NZ* Disaable PPP_Reconnect flag===================================================================v1.00B06.NZ* Allow the use of the character "&" in the PPP password field.===================================================================v1.00B05.NZ* Add UPnP page.* Enable UPnP by deafult.* Fix DNS Pass Through failed when DNS relay is disabled. (Fix it by using Primary DNS of Home->DNS setting if DNS Relay is disabled)* Fix the source IP of the packet to be changed to local IP after port forwarding.* Corrected MAC Address Filtering and added Access List.* Add Wireless Clients option under Status tab.* Move Save & Reboot options to their own page.* Improved connectivity (Line Sync) with Ericsson and NEC DSLAMs.===================================================================v1.00B04.NZ* Default Connection: PPPoA VPI/VCI: 0/100* Security Protocol: PAP* User name: user@jetstreamgames.co.nz* Password: 123* Change "Apply" & "Save All" behaviors to be consistent (i.e. only save to flash when saveall)
How To Load Firmware (ver.2.0 or above) with ADSL2/2+ SupportADSL2/2+ firmware is backward compatible with non-ADSL2/2+ connections. If your modem/router is running firmware ver. 2.0 or above it already has ADSL2/2+ support.NOTE: Firmware upgrade requires certain steps. Please read this document prior to proceeding with the upgrade.Disclaimer: - D-Link Australia does not guarantee that this firmware is fully compatible with all Internet Providers' ADSL2/2+ DSLAMs.- Please confirm with your Internet Provider the availability of ADSL2/2+ services in your area.- Upgrading the modem/router to the ADSL2/2+ firmware is not reversible to firmware versions prior to 2.0 without returning the product to D-Link Australia RMA Dept. ADSL2/2+ firmware is however backward compatible with ADSL(1).UPGRADE STEPS:- You may have two options (see A or B) with the new firmware: (A) *PREFERRED OPTION* Firmware upgrade utility (EXE) file. Follow the steps listed below; (B) WEB Interface binary (WEB) file. This file can not be used if your router is running firmware older than ver. 2.0. If it has ver. 2.0 or above, the upgrade can be carried out through router's WEB interface via Tools > Firmware;(A) This option is not suitable for Windows Vista.- Download the EXE firmware file and save it into any folder on your computer.- FACTORY RESET the modem/router before upgrading.- Connect the modem/router directly to your computer via network cable (do not use wireless connection).- Disable Firewall/Antivirus software on your computer.- !!!IMPORTANT!!! You must assign a static IP address to your PC before upgrading the firwmare, otherwise it will corrupt your unit. Steps: Go to Control Panel > Network Connections > Local Area Connection > Properties > Internet Protocol TCP/IP > Properties > IP address: 10.1.1.5, Subnet Mask 255.0.0.0, Default Gateway 10.1.1.1.- Run the firmware upgrade utility. When prompted, enter the unit's IP address (10.1.1.1) and username/password (admin/admin).- Do not turn the unit off while loading firmware.- After the firmware is loaded check the version under Tools > Firmware. You can now change your computer back to 'Obtain IP Address Automatically'. - Reconfigure the router according to your ISP's requirements. - Save the settings under Tools > [System] > Save & Reboot.(B) - Download the WEB firmware file and save it into any folder on your computer. - FACTORY RESET the modem/router before upgrading.- Connect the modem/router directly to your computer via network cable (do not use wireless connection).- Disable Firewall/Antivirus software on your computer.- Log into your modem/router via http://10.1.1.1. - Click on Tools > Firmware > Browse... Select the downloaded firmware file and click Open and then Apply.- Wait until the router completes the firmware update and reboots.- Reconfigure the modem/router according to your ISP's requirements. - Save the settings under Tools > [System] > Save & Reboot.NOTE: This firmware is only suitable for modems/routers distributed inAustralia. If you bought your router outside Australia or New Zealand the firmware upgrade may damage your router and void the Warranty.
V3.00B02.NZ 20060711 WEB
DLinkNZ DSL-G604T singleimage kernel fs V3.00B02.NZ.20060711 (2.57 MB)
Download.
v3.00B02.NZ 20060711 EXE
DSL-G604T V3.00B02.NZ.20060711.exe (3.3 MB)
Download.
READ ME - How to Recover Router
How to Recover Router.zip (181.98 KB)
Download.
Other Documents
Software
No Software Available.pdf (22.85 KB)
Download.
SNMP
No SNMP Available.pdf (22.99 KB)
Download.
SetupGuides
How to Open Ports in DSL-xxxT FW v2.x or above.pdf (289.07 KB)
Download.
How to Open Ports in DSL-xxxT FW v1.x.pdf (165.9 KB)
Download.
Advanced Filters Setup in DSL-G604T.pdf (1.52 MB)
Download.
How To Recover Router With Corrupted Firmware
How to Recover Router.zip (181.78 KB)
Download.
ScreenCaptures
DSL-G604T Screenies FW-v1.00B06.NZ.pdf (1.95 MB)
Download.
QuickInstallGuide
DSL-G604T QIG v1.00.pdf (758.02 KB)
Download.
Manuals
v4.00
DSL-G604T Manual v4.00.pdf (3.16 MB)
Download.
Drivers
No Drivers Required.pdf (22.6 KB)
Download.