D-Link Support Resources

DSL-504T Firmware Release Notes

v2.00B13.AU_20070425

1. Port redirection to a different port fix.
2. LAN Client base IP restriction removed.

v2.00B08.AU_20060904

* Fixed Status page Gateway IP address not shown
* Fixed PPPD doesn't send PADT when doing"Save and Reboot"
* Multiple port redirection fixed

v2.00B07.AU_20060808

* Fixed firewall rule �Ping from external network�.
* LAN Client valid range is restricted by the DHCP range changed.
* Fixed pinging both LAN and WAN IPs at the same time.

V2.00B05.AU_20060710

* Fix P2P lockups
* Fix WAN page not displaying correct settings

v2.00B04.AU_20060601

* Corrected the photo of DSL-504T
* Increased amount of NAT sessions that can be handled
* Fixed Keep Alive for connections to certain ISPs

v2.00B02.AU_20050812

* Adds Feature to change Web GUI port number.

===========================================================
v2.00B02.AU_20050812

=] NOTE [=
- You will need to update to v2.00B01T01.AU (if still running v1.00B06.AU or lower) before being able to update to this firwmare.

* Fixes PlayStation 2 DNAS Authentication Issues.
* Backup, Load Config Feature added.
* Enables UPnP by Default.

===========================================================
v2.00B01T01.AU

=] NOTE [=
- It is advised to FACTORY RESET the unit before upgrading.
- You must assign a static IP address to your PC (same subnet) before upgrading the firwmare otherwise it will corrupt your unit. eg: IP: 10.1.1.5, Subnet 255.0.0.0
- You cannot downgrade to previous firmwares once you have upgraded to v2.00B01T01.AU

* ADSL 2/2+ Support (only available with selected ISPs)
* Add Dynamic DNS Support - www.dyndys.org, www.no-ip.org
* Add SNMP Support - v1, v2c
* New Port Forwarding Feature with Predefined Items
* Add LAN Clients page for Port Forwarding Feature
* Add Static DHCP Feature
* Add Bridge Filters Feature
* Add IGMP Feature
* Add Remote Log Feature

===========================================================
V1.00B06

* Support PPPoe/PPPoa username and password can contain character '&'
* Initial Release

How To Load Firmware (ver.2.0 or above) with ADSL2/2+ Support

ADSL2/2+ firmware is backward compatible with non-ADSL2/2+ connections.
If your modem/router is running firmware ver. 2.0 or above it already
has ADSL2/2+ support.

NOTE: Firmware upgrade requires certain steps. Please read
this document prior to proceeding with the upgrade.

Disclaimer:
- D-Link Australia does not guarantee that this firmware
is fully compatible with all Internet Providers' ADSL2/2+ DSLAMs.
- Please confirm with your Internet Provider the availability
of ADSL2/2+ services in your area.
- Upgrading the modem/router to the ADSL2/2+ firmware is not
reversible to firmware versions prior to 2.0 without returning the
product to D-Link Australia RMA Dept. ADSL2/2+ firmware is however
backward compatible with ADSL(1).

UPGRADE STEPS:
- You may have two options (see A or B) with the new firmware:
(A) *PREFERRED OPTION* Firmware upgrade utility (EXE) file.
Follow the steps listed below;
(B) WEB Interface binary (WEB) file.
This file can not be used if your router is running firmware older
than ver. 2.0. If it has ver. 2.0 or above, the upgrade can be
carried out through router's WEB interface via Tools > Firmware;

(A) This option is not suitable for Windows Vista.
- Download the EXE firmware file and save it into any folder on
your computer.
- FACTORY RESET the modem/router before upgrading.
- Connect the modem/router directly to your computer via network cable
(do not use wireless connection).
- Disable Firewall/Antivirus software on your computer.
- !!!IMPORTANT!!! You must assign a static IP address to your PC
before upgrading the firwmare, otherwise it will corrupt your unit.
Steps: Go to Control Panel > Network Connections > Local Area Connection >
Properties > Internet Protocol TCP/IP > Properties >
IP address: 10.1.1.5,
Subnet Mask 255.0.0.0,
Default Gateway 10.1.1.1.
- Run the firmware upgrade utility.
When prompted, enter the unit's IP address (10.1.1.1)
and username/password (admin/admin).
- Do not turn the unit off while loading firmware.
- After the firmware is loaded check the version under Tools > Firmware.
You can now change your computer back to 'Obtain IP Address Automatically'.
- Reconfigure the router according to your ISP's requirements.
- Save the settings under Tools > [System] > Save & Reboot.

(B)
- Download the WEB firmware file and save it into any folder on
your computer.
- FACTORY RESET the modem/router before upgrading.
- Connect the modem/router directly to your computer via network cable
(do not use wireless connection).
- Disable Firewall/Antivirus software on your computer.
- Log into your modem/router via http://10.1.1.1.
- Click on Tools > Firmware > Browse... Select the downloaded firmware file
and click Open and then Apply.
- Wait until the router completes the firmware update and reboots.
- Reconfigure the modem/router according to your ISP's requirements.
- Save the settings under Tools > [System] > Save & Reboot.

NOTE: This firmware is only suitable for modems/routers distributed in
Australia. If you bought your router outside Australia or New Zealand
the firmware upgrade may damage your router and void the Warranty.

READ ME - How to Recover Router

How to Recover Router.zip (181.98 KB)

Download.

Firmware v2.00B13.AU WEB

DLinkAU DSL-504T singleimage kernel fs V2.00B13.AU 20070425 (2.04 MB)

Download.

Firmware v2.00B13.AU EXE

DSL-504T V2.00B13.AU 20070425.zip (2.65 MB)

Download.

Drivers

No Drivers Required.pdf (22.6 KB)

Download.